| Overall Length | 29.2ft in |
|---|---|
| Width Over Tires | 8.47ft in |
| Wheelbase | 20.1ft in |
| Rear Ground Clearance | 1.13ft in |
| Tandem Axle Wheelbase | 5ft in |
| Front Ground Clearance | 1.97ft in |
| Blade Base | 8.39ft in |
| Height To Top Of Isomount Cab | 10.79ft in |
| Pry-Out Force | 258201lb |
| Ripping Depth - Maximum | 16.8in |
| Ripper Shank Holders | 5 |
| Penetration Force | 20443lb |
| Ripper Shank Holder Spacing | 21in |
| Number Of Cylinders | 6 |
| Engine Make | 2236 |
| Front Frame Structure - Height | 1.1ft in |
| Front Frame Structure - Width | 0.9ft in |
| Power Measured @ | 2100rpm |
| Torque Measured @ | 2100rpm |
| Net Power Gears 7-8 | 283hp |
| Net Torque Gears 7-8 | 1000lb ft |
| Bore | 4.5in |
| Stroke | 5.9in |
| Emissions | U.S. Tier 4 Interim/EU Stage IIIB |
| Engine Model | Cat C9.3 ACERT |
| Derating Altitude | 10000ft in |
| Maximum Torque | 1000lb ft |
| Base Power (1st Gear) - Net | 213hp |
| Standard Capability | 109degrees |
| Speed At Rated Power | 2,100 rpm |
| High - Ambient Capability | 122degrees |
| Awd Range - Net | 166-211 kW (223-283 hp) |
| Awd Range - Net - Metric | 166-211 kW (226-287 hp) |
| Vhp Plus Range - Net | 159-196 kW (213-263 hp) |
| Vhp Plus Range - Net - Metric | 159-196 kW (216-267 hp) |
| Circle - Diameter | 60.2in |
| Drawbar - Height | 6in |
| Front Axle - Height To Center | 23.6in |
| Circle - Blade Beam Thickness | 1.6in |
| Drawbar - Thickness | 0.5in |
| Drawbar - Width | 3in |
| Front-Top/Bottom Plate - Width | 12in |
| Vhp Plus - Gear 1f, Net | 213hp |
| Vhp Plus - Gear 2f, Net | 223hp |
| Vhp Plus - Gear 3f, Net | 233hp |
| Vhp Plus - Gear 4f, Net | 243hp |
| Vhp Plus - Gear 5f, Net | 248hp |
| Vhp Plus - Gear 6f, Net | 253hp |
| Vhp Plus - Gear 7f, Net | 258hp |
| Vhp Plus - Gear 8f, Net | 263hp |
| Base Power (All Gears) - Net | 213hp |
| Std Operation Weight - Total | 45221lb |
| Max Operation Weight - Total | 52795lb |
| Oil System Fluid Capacity | 7.9gal |
| Cooling System Fluid Capacity | 14.8gal |
| Transmission Fluid Capacity | 17.2gal |
| Circle Gearbox Fluid Capacity | 1.8gal |
| Operating Voltage | 24V |
| Alternator Supplied Amperage | 150amps |
| Brakes - Parking | Multiple Oil Disc |
| Brakes - Service | Multiple Oil Disc |
| Transmission | Direct Drive, Powershift |
| Forward/Reverse Gears | 8 Fwd/6 Rev |
| Brakes - Secondary | Dual Circuit Control |
| Brakes - Service - Surface Area | 3565in2 |
| Articulation Angle | 20degrees |
| Turning Radius | 25.5ft in |
| Transmission Type | direct drive, powershift |
| Number Of Gears - Forward | 8 |
| Number Of Gears - Reverse | 6 |
| Max Speed - Forward | 29mph |
| Max Speed - Reverse | 22.9mph |
| Wheel Lean | 18degrees |
| Oscillation - Total | 32degrees |
| Ground Clearance | 2ft in |
| Standby Pressure | 609 psi |
| Maximum System Pressure | 3503 psi |
| Moldboard Width | 14ft in |
| Max Depth Of Cut | 29.6in |
| Side Shift Left | 20.1in |
| Side Shift Right | 26in |
| Blade Pull At Max Weight | 20044lb |
| Blade Down Pressure | 22884lb |
| Pump Type | Variable piston |
| Pump Flow | 55.5gal/min |
| Relief Valve Pressure | 3503psi |
| Circuit Type | Parallel |
| Pump Output | 55.5 gal/min |
| Reservoir Tank Capacity | 15.9gal |
| Blade Width | 14ft in |
| Arc Radius | 16.3in |
| Throat Clearance | 6.5in |
| Cutting Edge Width | 6in |
| Cutting Edge Thickness | 0.6in |
| End Bit - Width | 6in |
| End Bit - Thickness | 0.6in |
| Moldboard Height | 24in |
| Moldboard Thickness | 0.9in |
| Blade Pull - Maximum Gvw | 34072lb |
| Blade Pull - Base Gvw | 25908lb |
| Blade Down Pressure - Base Gvw | 17171lb |
| Diameter | 60.3in |
| Rotation | 360degrees |
| Shift Left | 27.4in |
| Shift Right | 28.7in |
| Max Reach Outside Tires - Left | 82.3in |
| Max Reach Outside Tires - Right | 89.7in |
| Max Lift Above Ground | 17.8in |
| Blade Tip Angle - Front | 40degrees |
| Blade Tip Angle - Rear | 5degrees |
| Top Speed - Forward | 29.5mph |
| Top Speed - Reverse | 23.3mph |
| Steering Range - Left/Right | 47.5 degrees |
| Articulation Angle - Left/Right | 20 degrees |
| Forward - 8th | 29.5mph |
| Forward - 7th | 20.3mph |
| Forward - 6th | 14.7mph |
| Forward - 5th | 10.8mph |
| Forward - 4th | 7mph |
| Forward - 3rd | 5.1mph |
| Forward - 2nd | 3.5mph |
| Forward - 1st | 2.6mph |
| Reverse - 6th | 23.3mph |
| Reverse - 5th | 16mph |
| Reverse - 4th | 8.5mph |
| Reverse - 3rd | 5.5mph |
| Reverse - 2nd | 3.8mph |
| Reverse - 1st | 2mph |
| Brakes | ISO 3450, ISO 10265 |
| Rops/Fops | ISO 3471 / ISO 3499 |
| Sound | ISO 6394/ISO 6395 |
| Steering | ISO 5010 |
| Cooling System | 14.8gal |
| Hydraulic System - Total | 26.4gal |
| Engine Oil | 7.9gal |
| Hydraulic System Tank | 16.9gal |
| Tandem Housing - Each | 16.9gal |
| Circle Drive Housing | 1.8gal |
| Fuel Capacity | 110gal |
| Circle Centershift - Right | 28.7in |
| Circle Centershift - Left | 27.4in |
| Moldboard Sideshift - Right | 26in |
| Moldboard Sideshift - Left | 20.1in |
| Blade Tip Range Forward | 40 degrees |
| Blade Tip Range Backward | 5 degrees |
| Maximum Lift Above Ground | 17.8in |
| Maximum Depth Of Cut | 29.5in |
| Maximum Blade Position Angle | 90 degrees |
| Front, V-Type - Working Width | 47.4in |
| Mid, V-Type - Working Width | 46.6in |
| Rear - Working Width | 84in |
| Mid, Straight - Working Width | 70.9in |
| Height | 19.9in |
| Width | 8.3in |
| Sidewall Thickness - Inner | 0.7in |
| Sidewall Thickness - Outer | 0.8in |
| Drive Chain Pitch | 2in |
| Wheel Axle Spacing | 60in |
| Tandem Oscillation - Front Up | 15 degrees |
| Tandem Oscillation - Front Down | 25 degrees |
