Overall Length | 28.58ft in |
---|---|
Width Over Tires | 8.17ft in |
Wheelbase | 20.08ft in |
Rear Ground Clearance | 1.13ft in |
Tandem Axle Wheelbase | 5ft in |
Front Ground Clearance | 1.87ft in |
Blade Base | 8.39ft in |
Height - Top Of Cylinders | 119in |
Height To Top Of Isomount Cab | 10.8ft in |
Length - Between Tandem Axles | 60in |
Length - Push Plate To Ripper | 399in |
Height - Top Of Cab | 130ft in |
Height - Front Axle Center | 23.5in |
Height - Exhaust Stack | 121in |
Width - Outside Front Tires | 98in |
Width - Outside Rear Tires | 98in |
Width - Tire Center Lines | 84in |
Ground Clearance - Rear Axle | 13.3in |
Pry-Out Force | 26259lb |
Ripping Depth - Maximum | 16.8in |
Ripper Shank Holders | 5 |
Penetration Force | 20540lb |
Ripper Shank Holder Spacing | 21in |
Number Of Cylinders | 6 |
Engine Make | 2236 |
Front Frame Structure - Height | 12ft in |
Front Frame Structure - Width | 12ft in |
Power Measured @ | 2000rpm |
Max Power | 183hp |
Net Power Gears 7-8 | 183hp |
Displacement | 439cu in |
Bore | 4.3in |
Stroke | 5in |
Emissions | Emissions equivalent to U.S. EPA Tier 3 and EU Stage IIIA. |
Engine Model | Cat C7 ACERT |
Note (2) | Net power is tested per ISO 9249, SAE J1349, and EEC 80/1269 Standards in effect at the time of manufacture. |
Note (3) | Net power advertised is the power available at rated speed of 2,000 rpm, measured at the flywheel when engine is equipped with fan running at minimum speed, air cleaner, muffler and alternator. |
Note (4) | Power as declared per ISO 14396, Rated Speed = 2,000 rpm, VHP Plus = 175 kW (234 hp) |
Note (5) | No engine derating required up to 3048 m (10,000 ft). |
Derating Altitude | 10000ft in |
Base Power (1st Gear) - Net | 183hp |
Speed At Rated Power | 2000 RPM |
High - Ambient Capability | 122degrees |
Maximum Torque - Vhp Plus | 855lb ft |
Vhp Plus Range - Net | 136-174 kW (183-233 hp) |
Vhp Plus Range - Net - Metric | 136-174 kW (186-237 hp) |
Circle - Diameter | 60.2in |
Drawbar - Height | 6in |
Front Axle - Height To Center | 23in |
Circle - Blade Beam Thickness | 1.6in |
Drawbar - Width | 3in |
Torque Rise - Vhp Plus | 39% |
Standard - Fan Speed - Maximum | 1450 RPM |
Standard - Fan Speed - Minimum | 600 rpm |
Standard - Ambient Capability | 109degrees |
Std Operation Weight - Total | 33356lb |
Max Operation Weight - Total | 50875lb |
Cooling System Fluid Capacity | 12.4gal |
Circle Gearbox Fluid Capacity | 1.8gal |
Brakes - Parking | Multiple Oil Disc |
Brakes - Service | Multiple Oil Disc |
Transmission | Direct drive, power shift, countershaft |
Forward/Reverse Gears | 8 Forward/6 Reverse |
Brakes - Secondary | Dual circuit control system |
Brakes - Service - Surface Area | 3565in2 |
Articulation Angle | 20degrees |
Turning Radius | 25.5ft in |
Transmission Type | direct drive, power shift, countershaft |
Number Of Gears - Forward | 8 |
Number Of Gears - Reverse | 6 |
Max Speed - Forward | 29mph |
Max Speed - Reverse | 22.9mph |
Wheel Lean | 18degrees |
Oscillation - Total | 32degrees |
Ground Clearance | 1.9ft in |
Standby Pressure | 450 psi |
Maximum System Pressure | 3500 psi |
Max Depth Of Cut | 28.1in |
Side Shift Left | 20.1in |
Side Shift Right | 26in |
Blade Pull At Max Weight | 45787.8lb |
Pump Type | Variable piston |
Pump Flow | 55.7gal/min |
Relief Valve Pressure | 3500psi |
Circuit Type | Electro-hydraulic load sensing, closed center |
Pump Output | 55.7 gal/min |
Blade Width | 12ft in |
Arc Radius | 16.3in |
Throat Clearance | 6.5in |
Cutting Edge Width | 6in |
Cutting Edge Thickness | 0.6in |
End Bit - Width | 6in |
End Bit - Thickness | 0.6in |
Moldboard Height | 24in |
Moldboard Thickness | 0.9in |
Moldboard Width | 12ft in |
Note | Blade pull calculated at 0.9 traction coefficient, which is equal to no-slip conditions, and Gross Vehicle Weight (GVW). |
Blade Pull - Maximum Gvw | 31758lb |
Blade Pull - Base Gvw | 24294lb |
Down Pressure - Maximum Gvw | 28503lb |
Down Pressure - Base Gvw | 16410lb |
Diameter | 60.2in |
Shift Left | 27.4in |
Shift Right | 28.7in |
Max Reach Outside Tires - Left | 70.5in |
Max Reach Outside Tires - Right | 77.9in |
Max Lift Above Ground | 18.9in |
Blade Tip Angle - Front | 40degrees |
Blade Tip Angle - Rear | 5degrees |
Top Speed - Forward | 29mph |
Top Speed - Reverse | 22.9mph |
Steering Range - Left/Right | 47.5 degrees |
Articulation Angle - Left/Right | 20 degrees |
Forward - 8th | 29mph |
Forward - 7th | 19.9mph |
Forward - 6th | 14.5mph |
Forward - 5th | 10.6mph |
Forward - 4th | 6.8mph |
Forward - 3rd | 5mph |
Forward - 2nd | 3.4mph |
Forward - 1st | 2.5mph |
Reverse - 6th | 22.9mph |
Reverse - 5th | 15.7mph |
Reverse - 4th | 8.4mph |
Reverse - 3rd | 5.4mph |
Reverse - 2nd | 3.7mph |
Reverse - 1st | 2mph |
Brakes | ISO 3450:1996 |
Rops/Fops | ISO 3471:2008, ISO 3449:2005 Level II |
Sound | ISO 6394:2008, ISO 6395:2008 |
Note (1) | The static sound operator pressure level measured according to ISO 6394:2008 for a cab offered by Caterpillar, when properly installed, maintained and tested with doors and windows closed and hydraul |
Steering | ISO 5010:2007 |
Cooling System | 10.6gal |
Engine Oil | 6.6gal |
Hydraulic System Tank | 16.9gal |
Tandem Housing - Each | 16.9gal |
Circle Drive Housing | 1.8gal |
Fuel Capacity | 110gal |
Circle Centershift - Right | 28.7in |
Circle Centershift - Left | 27.4in |
Moldboard Sideshift - Right | 26in |
Moldboard Sideshift - Left | 20.1in |
Blade Tip Range Forward | 40 degrees |
Blade Tip Range Backward | 5 degrees |
Maximum Lift Above Ground | 18.9in |
Maximum Depth Of Cut | 28.1in |
Maximum Blade Position Angle | 90 degrees |
Rear - Scarifier Shank Holders | 9 |
Mid, V-Type - Working Width | 46.6in |
Rear - Working Width | 91in |
Rear - Scarifying Depth, Maximum | 10.5in |
Height | 19.9in |
Width | 7.9in |
Sidewall Thickness - Inner | 0.6in |
Sidewall Thickness - Outer | 0.7in |
Drive Chain Pitch | 2in |
Wheel Axle Spacing | 60in |
Tandem Oscillation - Front Up | 15 degrees |
Tandem Oscillation - Front Down | 25 degrees |
Gear - Forward 1st | 183hp |
Gear - Forward 2nd | 188hp |
Gear - Forward 3rd | 203hp |
Gear - Forward 4th | 208hp |
Gear - Forward 5th | 213hp |
Gear - Forward 6th | 218hp |
Gear - Forward 7th | 233hp |
Gear - Forward 8th | 233hp |
Gear - Reverse 1st | 183hp |
Gear - Reverse 2nd | 188hp |
Gear - Reverse 3rd-6th | 203hp |