| Overall Length | 51.19ft in |
|---|---|
| Overall Height | 24.18ft in |
| Wheelbase | 21.82ft in |
| Turning Radius | 52.5ft in |
| Width Over Tires-Front | 24.68ft in |
| Width Over Tires-Rear | 27.33ft in |
| Ratio | 32.62:1 |
| Control | AC Torque Control System |
| Motorised Wheels | GDY108 Induction Traction Motors |
| Maximum Speed (Km/H) | 64.5 |
| Alternator | 24 volt, 250 amp |
| Lighting | 24 volt |
| Cranking Motors | Two/24 volt |
| Front | 328 |
| Rear | 239 |
| Capacity - Struck | 194.9yd3 |
| Heaped (2:1, Sae) | 280yd3 |
| Payload | 89999.4lb |
| Structure | Flat floor configuration |
| Weight | 89999.4lb |
| Canopy Sheet | 06mm 0.24' 690 Mpa 1,00,000 psi tensile strength steel |
| Front Sheet | 10 mm 0.39' Outer, 12mm 0.47' Center, 1379 mPa 200,000 psi tensile strength steel |
| Side Sheet | 10 mm 0.39' 1379 Mpa 2,00,000 psi tensile strength steel |
| Floor Sheet | 16 mm 0.63' Outer, 19mm 0.75' Center, 1379 mPa 200,000 psi tensile strength steel |
| Loading Height | 23.5ft in |
| Number Of Cylinders | 18 |
| Engine Make | 2238 |
| Engine Model | SSDA18V170 |
| Power Measured @ | 1900rpm |
| Displacement | 4759.9cu in |
| Fuel Type | diesel |
| Horse Power: Sae J1995 | 3500.1hp |
| Operating Cycle | 4-cycle |
| Weight (Wet) | 25904.4lb |
| Weight (Dry) | 24802.1lb |
| Service Brake Type | Oil-cooled, hydraulic-actuated, multiple disc brakes at each wheel. |
| Parking Brake Type | Multiple disc, spring-applied, hydraulically-released, dry brakes on inboard end of each wheel motor rotor shaft. Rated to hold on ±15% grade at maximum gross vehicle weight. |
| Emergency Brakes | Oil-cooled, multiple disc front & rearAutomatically applied prior to hydraulic system pressure dropping below level required to meet secondary stopping requirements. |
| Wheel Brake Locks | Switch-activated |
| Fuel Tank | 1400.2gal |
| Cooling System | 190gal |
| Hydraulic System | 350.1gal |
| Crankcase | 90.1gal |
| Motor Gear Box | 25.1gal |
| Gross Weight | 1270021.3lb |
| Empty Weight | 549998.2lb |
| Standard Tire | 53/80 R63 |
| Hoist Cylinder | Two 3-stage dual-acting outbound cylinders and internal cushion valve, over-centre damping. |
| Relief Pressure | Hoist and brake cooling- 17237 kPa 2,500 psi Steering and brake-20685 kPa 3,000 psi |
| Hoist Time | Power-up loaded: 24 sec, Power-down: 14 sec, Float-down empty:24 sec |
| Turning Circle Diameter (Sae) | 105ft in |
| Reservoir | 250gal |
| Filtration | In-line replaceable elements |
| Suction | Single, full flow, 100 mesh |
| Hoist And Steering | Dual, in-line, high pressure |
| Pumps | Two pumps, single package, end of alternator |
